离子风机的除静电效果好不好主要取决于什么呢?说出来或许我们都不信赖,不是风机的转数,不是风机的体型,而是那根小小的放电针。
离子风机放电针用金属材料制成,一般使用不锈钢(SUS)、金属锗(Ge)、镍(Ni)、钛(Ti)、金属钨(W)等耐腐蚀材料制成,不锈钢由于价格低被广泛使用,金属钨较不锈钢更耐磨损、耐腐蚀也被广泛使用。
由于离子风机放电针在长时间使用后会受到污染,直接影响到除电功能和离子平衡,所以使用时应常常守时清洗除电电极部,特别是直流式除电器放电针更易受污染,比起交流式除电器清洗应更一再,并且正极和负极放电针磨损的程度不同,需要做守时的离子平衡检测,在放电针磨损程度严峻时还应及时更换放电针。因此,从这一点上,交流式的离子风机除静电效果会比直流的要好!
守时的清洗放电针也是很麻烦的一件作业,从大型车间来说,不光降低了生产效率,也增加了风机保养成本,日前,KESD有一款自动清洁的离子风机刚好解决了这个问题。只需经过一个小小的按钮,就能完结离子风机的自我清洁。从保养上面大大节省了成本。
静电防护原理:
(1)对或许发生静电的当地要防止静电积累。采取方法在安全范围内。
(2)对现已存在的静电积累敏捷消除掉,即时开释。
静电防护方法
(1)使用防静电材料:金属是导体,因导体的漏放电流大,会损坏器件。别的由于绝缘材料容易发生冲突起电,因此不能选用金属和绝缘材料作防静电材料。而是选用表面电阻l×105Ω·cm以下的所谓静电导体,以及表面电阻1×105-1×108Ω·cm的静电亚导体作为防静电材料。例如常用的静电防护材料是在橡胶中混入导电碳黑来完结的,将表面电阻控制在1×106Ω·cm以下。
(2)泄露与接地:对或许发生或现已发生静电的部位进行接地,供给静电开释通道。选用埋大地线的方法树立“独立”地线。使地线与大地之间的电阻<10Ω。
静电防护材料接地方法:将静电防护材料(如于作台面垫、地垫、防静电腕带等)经过1MΩ的电阻接到通向独立大地线的导体上。串接1MΩ电阻是为了确保对地泄放<5mA的电流,称为软接地。设备外壳和静电屏蔽罩通常是直接接地,称为硬接地。
(3)导体带静电的消除:导体上的静电能够用接地的方法使静电泄露到大地。放电体卜的电压与开释时间可用下式标明:
UT=U0L1/RC
式中UT-T时间的电压(V)U0一起始电压(V)R-等效电阻(Ω)C-导体等效电容(pf)
一般要求在1秒内将静电泄露。即1秒内将电压降至1OOV以下的安全区。这样能够防止泄露速度过快、泄露电流过大对SSD构成损坏。若U0=500V,C=200pf,想在1秒内使UT抵达100V,则要求R=1.28×109Ω。因此静电防护系统中通常用1MΩ的限流电阻,将泄放电流限制在5mA以下。这是为操作安全规划的。假如操作人员在静电防护系统中,不小心触及到220V工业电压,也不会带来危险。
0769-85900834